Home/Stories/The same box, one more circuit
Teardown NS03

The same box, one more circuit

NS03 adds a 5 V output to a 15.4 mm body without changing the carton. The circuit is the easy part; keeping the packaging identical is the design work.

15 November 2026  ·  5 min read  ·  words by the design team
NS03 Hand Warmer Power Bank

NS03 is the NS02 with a power output. Same cell, same three heat bands, same 15.4 mm body, and — the part that took the longest — the same 153 × 108 × 16.5 mm retail box. Adding a circuit inside a product is a schematic problem. Adding it without changing the packaging is a logistics problem, and logistics is where the money is.

Two NS03 hand warmers, one black and one rose, standing on an orange studio backdrop
NS03 in black and rose. Same shell, same cell, same 153 × 108 × 16.5 mm carton as NS02 — the difference is a board and a port.

01 — What 2000 mAh actually means

The cell is 3.7 V at 2000 mAh, so 7.4 Wh. A current phone carries something like 17 to 18 Wh. After the boost converter's losses, NS03 can put roughly a third of a phone charge into a phone — enough to get you to the taxi rank, not enough to get you through an evening of photographs.

Bar chart comparing the energy in the NS03 cell, the energy delivered after the boost converter and a phone battery
Energy, drawn honestly. 7.4 Wh in the cell, about 6 Wh at the end of the cable, 17 in a current phone.

We could have fitted a bigger cell. The 103450 is 10.3 mm thick; a 12 mm cell would have added almost two millimetres to the body, taken the retail box to about 18.5 mm, and a padded mailer around that lands near 20.5 — over the US flat limit and over the German one. The margin we had was one millimetre. A bigger battery spends it.

So the cell stayed, and the promise is deliberately modest: this is a warmer that can rescue a phone, not a power bank that happens to be warm.

02 — Where the board went

Fifteen point four millimetres, total. The cell takes 10.3. That leaves 5.1 mm for two shells, the heating film, the display stack and a PCB. On NS02 the board is a single-sided controller the size of a postage stamp. On NS03 it is a boost converter with an inductor, a USB-C receptacle that now has to work in both directions, and a small forest of protection parts.

The inductor is 4 × 4 × 2 mm and it sits beside the cell, in the gap that the cell's rounded corner leaves, rather than on top of it. That is the whole trick: the board did not get thinner, it got reorganised into space that was already empty.

Cross-section diagram of the NS03 body showing the shells, heating film, cell and boost board and their thicknesses
The 15.4 mm budget, layer by layer. The board did not get thinner — it moved into the gap the cell's rounded corner leaves.

Heat was the harder constraint. The heating film is on the front face; the board is on the back, with the cell between them. An NTC on the cell tells the controller when to derate. Charging a phone with a 50 °C hand warmer pressed against the same pocket is how cells swell, so the output cuts back once the case passes the mid-forties.

There is no fast charge. Five volts at one amp is what the thermal budget allows in a sealed 15.4 mm shell, and a 9 V handshake would have meant a larger inductor and a hotter board for a feature that saves twenty minutes on an emergency top-up.

The magnetic back plate and the unit it snaps onto. The plate is where the output circuit breathes.
The magnetic back plate and the unit it snaps onto. The plate is where the output circuit breathes.

The magnetic back is not decoration. It is a 1.2 mm steel plate that stiffens the rear shell, spreads heat away from the board and gives the pair something to hold on to when two units are joined.

It also means NS03 can be clipped to a pocket lining or a bag strap, which is how most people carry a warmer when they are not holding it.

03 — Two grams the wrong way

NS02 weighs 120 g. NS03 weighs 118 g. The version with the extra circuit is lighter, which reads like a typo on the specification sheet. We put both on the same scale three times before we believed it.

Side by side comparison of NS02 at 120 grams and NS03 at 118 grams
Same scale, same hour, three passes each. The version with the extra circuit is the lighter one.

The explanation is unglamorous: the output board replaced a steel stiffener that NS02 carries behind its front face. The board is thinner than the plate it displaced, and the difference comes out at about two grams. We left the numbers as they measured. Buyers compare grams, and a spec sheet that rounds toward the nicer story is the beginning of a bad relationship.

04 — One carton, two SKUs

The retail box is unchanged: 153 × 108 × 16.5 mm, the same pulp tray, the same 61.3 mm column for the cable and manual. A carton holds 40 boxes — 80 units — at 36.7 × 32 × 23.3 cm and 13.7 kg gross.

That is the point of the whole exercise. A distributor can put NS02 and NS03 in the same carton, on the same pallet, under the same postal band. Adding the second SKU costs one more line on the order form; it does not cost a second packaging qualification, a second carton size or a second freight calculation.

For a retailer it means one shelf position can hold both, and the customer chooses between warmth and warmth-plus-a-charger without the shop having to explain why one of them ships for more. For the end buyer the second product arrives at the same postage as the first, which sounds minor until you are the one selling a €30 gift with free delivery.

Top view drawing of the NS03 retail box tray with two units and accessories
Tray cavity, drawn to scale. Two 54 mm units join to 108 mm, and the leftover 61.3 mm is where the cable and manual live.

05 — Cold is hard on lithium

A hand warmer spends its life in exactly the conditions its battery dislikes. Below 0 °C you should not charge a lithium cell; the plating that forms on the anode during a cold charge does not come back, and capacity quietly disappears over a season.

Discharge is gentler but still lossy: at −5 °C expect 20 to 30% less than the rated capacity. The design helps a little, because the cell sits directly behind the heating film — a unit that has been running for ten minutes keeps its own battery warmer than the air around it.

Chart of lithium battery capacity at 25 and minus 5 degrees Celsius, with the sub-zero range marked as unsuitable for charging
Capacity against temperature. Left of zero is a good place to store a warmer and a bad place to charge one.

The advice on the leaflet is the advice we give in person: charge it indoors, carry it in an inside pocket, and do not leave it in a car overnight in January and expect a full day of heat in the morning.

Two products, one box, one postal band. The second SKU should not cost the buyer a second logistics decision.

118grams
15.4mm body
2000mAh
16.5mm box
5V output
40boxes / carton
NS03 Hand Warmer Power Bank
The product in this story NS03 Hand Warmer Power Bank Warm hands, charged phone
View specification
Next story Three kinds of cold in one hand